Edatec HMI2020 based on CM4

DescriptionED-HMI2020-101C◆ FeaturesRasberry Pi CM4-based 10.1″ Industrial Tablet PC10.1″ WSVGA TFT, 1280×800 resolution, multi-point capacitive touchscreenBroadcom BCM2711 4-core Cortex-A72 64-bit processorUp to 8GB of LPDDR4 RAM and 32GB of eMMCLAN port rate supports up to 1Gbps2.4GHz & 5GHz Wi-Fi and Bluetooth wireless methodSupport micro-SD Card, integrated RTC, EEPROM and encryption chip9V~28V wide voltage power input with over-current, over-voltage, reverse connection and surge protectionHigh quality metal case, support embedded installation◆ Documents DownloadDatasheet Download Application Guide Download User Manual Download◆ SpecificationsSystemCPUBroadcom BCM2711, quad core Cortex-A72 (ARM v8) 64-bit SoC @ 1.5GHzVPUH.265(HEVC), up to 4Kp60 decodeH.264, up to 1080p60 decode, 1080p30 encode)GPUOpenGL ES 3.1 & Vulkan 1.0MemoryOptions for 1GB, 2GB, 4GB, 8GB LPDDR4-3200 SDRAMStorage– Options for 8GB, 16GB, 32GB eMMC storage– Micro SD card (user storage expansion)SoftwareOperating System– Raspberry Pi OS(Desktop) 32-bit– Raspberry Pi OS(Lite) 32-bit– Raspberry Pi OS(Desktop) 64-bit– Raspberry Pi OS(Lite) 64-bitFront I/OCamera Built-in 800M front cameraSide I/OPower1 x DC IN, DC Jack connector, supports 9V~28V input.Audio1 x Audio In/Stereo Out, 3.5mm audio jack connector. It can be used as MIC IN and LNE OUT.– When a headphone is connected, the audio output switches to the headphone.– When no headphone is connected, the audio output switches to the speaker1000MEthernet1 x adaptive 10/100/1000M ethernet port, RJ45 connector. It can be used to access the network. PoE can be supported through expansion moduleSD Card Slot 1 x Micro-SD card slot, uses to install SD card for storing user data.HDMI1 x HDMI port, type A connector. It compatibles with HDMI2.1 standard and supports 4K 60Hz.USB 2.0 2 x USB2.0 ports, type A connector, support up to 480Mbps.Antenna1 x SMA port, uses to connect Wi-Fi/BT antenna.Speaker1 x PA output, dual channel stereo audio output, built-in two 4Ω 5W speakers.Buttons and IndicatorsReset1 x Reset button, which can reset the device.Rpiboot1 x Rpiboot button, uses to flash eMMC for the system.PWR1 x red power indicator, uses to check the status of device power-on and power-off.ACT1 x green system indicator, uses to check the working status of device.Expansion PerformanceEEPROMSupports 4K byte storage and improves the ease of use of device.CryptoAuthenticationIt can be matched to realize the required upper layer application and improves the security of device.RTC Ensure that the system clock is not affected by device power-off.Note: A CR1220 battery is provided by default in China.BuzzerA tip or an abnormity can be configurated according to actual application, which realizes the alarm function.Expansion I/O12V 1A1 x DC OUT, 2-Pin 2.0mm spacing connector, support 12V 1A output. These pinsare defined as GND/12V, reserve to provide power supply for extended LCD.40-pin GPIO1 x GPIO, 2×20-Pin 2.54mm pitch header, uses to lead out the GPIO ports of CM4.– These pins are defined as GPIO1~GPIO27/3V3/5V2/GND.– Compatibles with expansion modules, and reserves to connect expansion accessories.HDMI 1 x FPC HDMI, 40-pin 0.5mm spacing FPC connector, which can be reserved to connect extended LCD, supports USB/I2C touch screen and backlight adjustment.USB 1 x USB 2.0, 5-pin 1.27mm spacing FPC connector, supports to expand the USB2.0 interface.LCDLCD Size10.1″ WSVGA TFTResolution1280×800Colors16.7MBActive Area 135.36mm(H) x 216.576mm(V)BacklightLEDMTBF>30000hPixel Pitch0.169mm x 0.169mmLuminance350cd/m^2Contrast Ratio  1000:1Response Time30msViewing Angle (H/V)80°/80°Touch ScreenTypeMulti-point Capacitive Touch ScreenTransmittance≥85％Connection MethodCOFController InterfaceI2CDriver SupportLinuxMulti-touch10 pointsSurface Hardness6HElectrical CharacteristicsInput Voltage9V ~ 28V DCMaximum Power  Consumption20WMechanical CharacteristicsDimensions263mm x 177mm x 40mm (WxDxH, antenna is not included.)Weight 1.1KgInstallation Embeded installation, including front installation and rear installation.WirelessWi-Fi (optional)2.4GHz and 5GHz dual-band Wi-Fi with antenna.– 2.4GHz Wi-Fi: Compatible with IEEE 802.11 b/g/n– 5GHz Wi-Fi: Compatible with IEEE 802.11 a/n/acBluetooth  (optional)Bluetooth 5.0 with antenna, compatible with 2402MHz ~ 2480MHz frequency.Environmental & RegulatoryOperatingTemperature0°C ~ 50°CStorageTemperature-10°C ~ 60°CAmbient Humidity20% ~ 90%(non-condensing)CertificationsFCCFCC 47 CFR Part 15 Subpart B CEEN IEC 62368-1/EN IEC 62311/EN IEC 61000-3-2/EN IEC 61000-3-3EN 55032/EN 55035/EN 301 489-1/EN 301 489-3/EN 301 489-17/EN 301 489-52EN 301 328/EN 301 440/EN 301 511/EN 301 908-1/EN 301 908-2◆ System Block Diagram◆ Dimension Unit:mm◆ Oder Information